![]() "C:\Program Files\cwRsync\bin\rsync.exe" -config "C:\Program Files\cwRsync\bin\conf\nf" -daemon -log-file "C:\Program Files\ cwRsync\bin\log\rsyncservice.log" -address 192.168.1.5Ĭonfig nf - specify where the configuration file is located. If you specify something like path=/cygdrive/c/backup/, the client will exit with an error, and the log will show: 6 13:27:35 name lookup failed for 127.0.0.1: Unknown server error 6 13:27:35 connect from UNKNOWN (127.0.0.1) 6 13:27:35 rsync: chdir / failed: No such file or directory (2)īut when you specify the folder name in the client parameters, then everything works. I never managed to get the client to exchange files with the server, if you specify the path to the folder in the path. hosts allow = 192.168.1.6 # Only allow access to Server#2 # Drive label C path = /cygdrive/c/ comment = this is system drive read only = true #Drive label D path = /cygdrive/d/ comment = this is date drive read only = true #transfer logging = yes # End of configuration file # use chroot = yes – start rsync in chroot, for greater security – name of the module uid - must match the owner id of the directory we are going to write to path - full path to the directory to which we will write list = no - do not show the section in the listing comment – comment read only = false – open section for writing hosts allow - allow access to the push section only for certain addresses auth users = push - allow access only to the push user secrets file - file matching the username to a specific password. If we # set this to true, then rsync can only access drive C. # nf file # uid = user_id gid = user_id use chroot = false # Give permission to use all drives, not just C. Create a file in the conf folder nf the following content: Let's create in c:\Program Files\cwRsync\bin\ folders conf And log. ![]() Therefore, recommendations may not be followed.įirst you need to create a config. Also, when configuring, I used direct paths. in an option when calling rsync.Īfter installation, I did not observe any problems with encoding or work. In order for files with non-ascii characters in their names to be transferred normally, add -iconv=. you need to download the cygwin.dll file from and replace it with the one that comes with cwRsync. Solve the problem with non-ascii characters. cwRsync install to c:\Program Files\cwRsync\.Īfter installation, you can follow these recommendations:Īdd $CYGWIN_INSTALL_PATH/bin/ to the PATH environment variableĬontrol Panel -> System -> Advanced -> Environment Variables The installation process is quite simple: all values can be left by default. We need to install it on all cluster nodes. Before installing, you should make sure that it is compatible with the configs of the old version. The installer can be downloaded from here. Interaction occurs via local IP addresses:įirst you need to download and install the cwRsync utility. With a certain frequency, a client is launched on the second server, which connects to the socket of the first server, after which synchronization occurs. ![]() The client is configured on the second server (Server#2). The config specifies which resources will be accessed. 1), the cwRsync daemon starts at system startup. The principle of synchronization using cwRsync is as follows: on the main server (in our case, Server No. I got most of the information from, because the launch options for Rsync and cwRsync remain the same. I did not find any Russian-language articles on working with cwRsync - everyone copies the four installation steps together, and does not touch on work and configuration. In this article, we will look at how synchronization is configured. Also, the feedback from the admins about Rsync under Unix was very positive, and I decided to give it a try. In my case, the ability to interact with Unix servers in the future was very pleasing. The essence of this project is that the Rsync utility is launched on Windows using the cygwin library. This is how the cwRsync project came to life. Many administrators have a need to synchronize directories between Unix-Windows servers. In the process of creating a cluster, the question arose: how can you ensure the synchronization of files and folders on individual nodes? After a short search for all sorts of ready-made solutions, I came across a well-known utility that works under Unix - Rsync.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |